Tractor & Construction Plant Wiki

A sidelifter transferring a container

A sidelifter is a specialised truck or semi-trailer used to hoist and transport ISO standard intermodal containers over longer distances.

The sidelifter loads and unloads containers via a pair of hydraulic powered cranes mounted at each end of the vehicle chassis. the cranes are designed to lift containers from the ground, from other vehicles including rolling stock, from railway wagons and directly from stacks on docks or aboard container ships. A standard sidelifter is also able to stack a container at a two containers´ height on the ground. If the sidelifter chassis is of 40´ length or more, the cranes of the sidelifter can be shifted hydraulically along the sidelifter chassis to be able to pick up either one 20´or one 40´ or two 20´ ISO containers at a time.


Sidelifter handling a 20ft ISO container

The sidelifter was invented during the 1960s by Klaus Transport-systeme GmbH of Germany, with a focus on the military operations. The Klaus Sidelifters were heavy and not cost effective in the commercial area. Klaus was bought by Steelbro in New Zealand, that has developed the Sidelifter to be lighter and commercially acceptable. It was also further developed by Hammar Maskin AB in Sweden. It has since become a commonly used vehicle in intermodal facilities worldwide. The principal alternative to the costly machinery of the sidelifter is the use of swap body containers, which are too light to be stacked but can be unloaded from a truck by means of foldable legs. Today the biggest manufacturers are Hammar, Valart, Boxloader and Steelbro, followed by others minor regional manufacturers.[citation needed]


Sidelifters generally have the following attributes:

  • Lifting cranes (sometimes called Crane Modules). The hydraulically powered cranes lift the container (from the ground, loading dock, another vehicle, railway wagon or from the top of another container placed on the ground or other location) on and off the chassis. These cranes are placed on top of the sidelifter chassis and they are normally able to travel along the chassis being shifted by hydraulic cylinders or hydraulic motors in order to load varying container lengths.
  • A power source. While typically the cranes are powered by a trailer mounted diesel engine or gasoline engine, the cranes are sometimes powered via a PTO from the truck or tractor.
  • Stabilizing legs. These are fitted with hydraulic legs which are necessary to permit the lifting of up to 44 tonnes (49 short tons; 43 long tons) loads without tilting the vehicle. These may be adjustable to assist operation on unlevel ground and facilitate greater safety margins and load limits when stacking containers.
  • Chains, which are attached from the top of the cranes to the corner castings at the base of the container(s) during lifting operations. There is a special linking device that when placed between two 20 ft containers allows the user to lock two 20 ft (2 TEU´s) containers together allowing the containerlifter to lift them as if they were a 40 ft container.
  • The tractor/cab, which pulls the trailer, and in some cases supplies power through the PTO.This tractor/cab always supplies the compressed air for the wheels' brakes of the sidelifter. Normally, the sidelifter can not be operated without being connected to the Tractor because even if the power pack is under the sidelifter, the tractor provides compressed air for the trailer brakes and also additional stability for the lifting operation.
  • The chassis, which bears the weight of the container when loaded, as well as supports the cranes.
  • The remote control, a device with joysticks & buttons typically attached via a multi-pair electric wire or via a radio signal and that allows the operator to walk around the container and view the unit from various different angles during operation.

Sidelifter machines are designed to lift up to a maximum of 44 tonnes (49 short tons; 43 long tons) though smaller machines exist.

In addition to controlling the raising and lowering of the cranes, the operator can sometimes tilt the chassis using the stabilising legs which provides a limited ability to operate on non-level ground.

Some sidelifters have a telescopic chassis, sometimes called trombone chassis, allowing the unit to expand and contract in order to accommodate 20 ft, 40ft or even 45 ft containers. These Trombone units are specially suited for small secondary roads where cornering is quite difficult with 40 ft trailers.


A sidelifter is rated for ISO containers with a specified maximum total weight and to a maximum distance from the sidelifter chassis (also called maximum reach or maximum radius). This information is located on a nameplate provided by the manufacturer, and loads must not exceed these specifications. Sidelifter units have been known to overturn like any other crane, especially when lifting weights that are heavier than the maximum allowed weight or when operating at a radius that is bigger than the maximum allowed radius. Sidelifter units must always be operated only by trained personnel. Safety devices such as Electronic Stability System that prevent the sidelifter from rolling over may be sometimes required by local legislations


Mobile container stacker / loaders

A Rubber tyred gantry crane is another device for loading containers on to trucks (as well as around the port).

Smallwikipedialogo.png This page uses some content from Wikipedia. The original article was at Sidelifter. The list of authors can be seen in the page history. As with Tractor & Construction Plant Wiki, the text of Wikipedia is available under the Creative Commons by Attribution License and/or GNU Free Documentation License. Please check page history for when the original article was copied to Wikia