This article includes a list of references, related reading or external links, but its sources remain unclear because it lacks inline citations. Please improve this article by introducing more precise citations where appropriate. (April 2009) |
BMC B-Series engine.jpg | |
Manufacturer | BMC |
---|---|
Production | 1954–80 |
Configuration | in-line 4 |
Displacement | 1.2–2.4 litres |
Cylinder block alloy | cast iron |
Cylinder head alloy | cast iron |
Valvetrain | pushrod or overhead cam |
Fuel type | petrol & diesel versions |
Cooling system | water |
The BMC B-series was a straight-4 internal combustion engine family, mostly used in motor cars, created by British company Austin Motor Company. The pre-cursor of the "B" series engine was a 1200 cc OHV engine which was used in the 1947 Austin A40 Devon. This A40 Devon engine was based on a pre-war Side-valve design. Austin realised that eventually they would need an engine that could power many of its forthcoming medium-sized cars, and this would require an engine of at least 1500 cc capacity. Since the A40 Devon engine could not have its capacity enlarged, a new engine was designed, which, although superficially similar, was longer and heavier than the A40 Devon engine. The design of this new engine commenced around January 1952, and was designated as the "B" series. Displacements ranged widely from 1.2 L to 2.4 L, the latter being an Australia only production six-cylinder variant. 1.5 L and 1.8 L displacements were most common. Petrol versions were produced in the greatest numbers, but diesel versions exist for both cars and marine applications.
The engine was of conventional construction with a one-piece crankcase and cylinder block in cast iron with the crankcase extending down to the lowest level of the main bearing caps, and with cylinder head also usually in cast iron. The sump was made from pressed steel. Early engines used a three-bearing crankshaft, but later engines used five bearings. On all except the rare twin overhead camshaft variant, the camshaft — which was chain driven and mounted low in the block — operated the overhead valves via pushrods and rocker arms. The two inlet ports in the non-crossflow cylinder head were shared between cylinders 1 + 2 and 3 + 4 and the three exhaust ports between cylinder 1, 2 + 3 and 4. Valve clearance was adjustable by screws on the rocker arms with access to the tappets by two side covers on the engine block, this feature being a hang over from side valve engine design[citation needed], but it provides easy access to the camshaft tappets.
Engine numbering[]
There were two series of engine numbers used; BMC changed the system at the end of 1956.
Early numbering system[]
Numbers were of the style "BP15GB" followed by a serial number, where:
- B = B series engine
- P = Pushrod
- 15 = capacity
- G = MG (for full list see Later numbering system below)
- The final letter is the version of the engine.
1957–70 numbering system[]
Numbers were of the style "15GB-U-H" plus a serial number, where:
- 15 = capacity
- G = MG (other letters were: A = Austin, B = Industrial, H = Miscellaneous, J = Commercial, M = Morris, R = Riley, V = Vanden Plas and W = Wolseley )
- B = B series engine
- U = Central gear change (other letters were: A = Automatic, M = Manumatic clutch, N = Column change, O = Overdrive and P = Police)
- H = High compression (alternatively L = Low compression)
1970 onwards numbering system[]
Numbers were simplified to "18 V" plus a serial number, where 18 represents the capacity and V = vertical, i.e. longitudinal (in-line, not vee-arranged) engine with rear-wheel drive, and H = Horizontal, i.e. transverse engine with front-wheel drive.[citation needed]
There was sometimes a country indicator after the first part of the code, e.g. "18V-Z" was use for some United States (except California) MG MGB engines.
Engine types[]
1.2 litre engines[]
The 1200 cc was the first version of the engine. The bore was 65.5 mm (2.58 in) and the stroke 89 mm (3.5 in). The maximum power output was 39 bhp (29 kW) at 4300 rpm.
After the formation of British Motor Corporation (BMC) it was used in the following vehicles:
- 1954–56 Morris Cowley
- 1954–56 Austin A40 Cambridge
- 1954–55 Nash Metropolitan 1200 (used unique "2G" engine prefix)
- Massey-Harris Combine Harvester
1.5 litre engines[]
The 1.5 L (1489 cc) version was first used in 1953 in the MG Magnette ZA in twin carburettor version and in 1954 in the Morris Oxford and Austin Cambridge. In 1957, it was used in the original MGA. Output in twin carburettor form was 68–72 bhp (51–54 kW) and 55 bhp (41 kW) with a single carburettor. Bore was 73.0251 mm (2.87500 in) and stroke was 89 mm (3.5 in).
There was also a diesel version of this engine size. Power output was 40 bhp (30 kW) at 4,000 rpm and torque 64 lbf·ft at 1,900 rpm.
Applications:
- 1954–61 Morris Oxford Marks II, III, IV, & V
- 1956–59 Morris Cowley
- 1956–62 Nash Metropolitan 1500
- 1955–58 MGA
- 1953–61 MG Magnette ZA, ZB, & Mark III
- 1956-61 Morris J2 1/2-ton vans
- 1956–58 Austin A50 Cambridge
- 1958–61 Austin A55 Cambridge
- 1956–58 Wolseley 15/50
- 1957–65 Wolseley 1500
- 1958–61 Wolseley 15/60
- 1957–61 Morris Commercial JB-type 1/2 - Ton vans
- 1957-61 Austin 101 1/2 - Ton vans
- 1957–65 Riley 1.5
- 1959–61 Riley 4/68
- 1959–65 Rochdale Olympic
- 1958–62 Morris Major and Austin Lancer Series I/II
- 1957–63 Tempo Matador
- Hindustan Ambassador
- International Harvester "Metro-Mite" delivery truck
- Navigator 1500 marine engine
- 1958–60 TVR Grantura Mark I
- 1960–62 TVR Grantura Mark II & IIA
- 1958-1959 Elva Courier
Twin-Cam engines[]
A special Twin-Cam (DOHC) version of the 1588 cc B-series engine was produced for the MGA. Output was 108 bhp (81 kW) at 6700 rpm in the high-compression (9.9:1) version and 100 bhp (75 kW) in the optional low-compression (8.3:1) version. The engine block was cast iron, but the crossflow eight-port cylinder head was of aluminium alloy. Drive to the twin camshafts was by chain from a gear-driven, half-speed shaft running in the space that would have been occupied by the conventional camshaft. This engine gained a reputation for being unreliable in service, especially in the high-compression version which needed high-octane fuel, but this has now been largely overcome. The piston burning habits — thought to be the result of ignition timing — was later discovered to be due to a vibration induced lean burn situation involving the float bowls, easily correctable by flexibly mounting the carburettors.
A total of 2,111 cars were built, in both coupé and roadster versions.
A very few engines with the special displacement of 1762 cc were produced for racing purposes.
Applications:
- 1958–60 MGA Twin-Cam
1.6 litre engines[]
The engine was enlarged to 1.6 L (1588 cc) in 1958 by increasing the bore to 75.4 mm (2.97 in).
Applications:
- 1959–61 MGA 1600
- 1960–62 TVR Grantura Mark II, IIA
- 1959-61 Elva Courier Mark II
1.6 litre Mark II engines[]
The engine was enlarged to 1622 cc in 1961 with another bore increase, this time to 76.2 mm (3.00 in).
Applications:
- 1961–62 MGA Mark II
- 1961–69 Austin Cambridge A60
- 1961-67 Morris J2 1/2-ton vans
- 1961–71 Morris Oxford VI
- 1961–71 Wolseley 16/60
- 1961–69 Riley 4/72
- 1961–68 MG Magnette Mark IV
- 1961–67 Austin 152 & Morris J2 1/2-ton van
- 1974–78 Sherpa van
- 1962–64 Morris Major Elite
- 1963–66 Tempo Matador
- 1966–67 Hanomag Matador
- 1967–73 Hanomag F20, Hanomag F25, Hanomag F30, Hanomag F35
- 1970–73 Mercedes Benz L206, Mercedes Benz L306
- Navigator 1600 marine engine
- 1962–64 TVR Grantura Mark III
- 1963-64 Elva Courier Mark III
1.8 litre engines[]
The engine was enlarged again to 1.8 L (1798 cc) in 1962. Bore was 80.26 mm (3.160 in) and stroke was still 89 mm (3.5 in). The engine at first had a three-bearing crankshaft with a five-bearing version appearing in 1964.
There was also a diesel version of this capacity, used in the Leyland Sherpa van, and built under license in Turkey for many years. It is still widely used on narrowboats on the canals of the UK.
Applications:
- 1954–80 Probe 16
- 1962–80 MGB
- 1964–75 BMC ADO17 ("Landcrab") Austin 1800
- 1967–72 BMC ADO17 ("Landcrab") Wolseley 18/85
- 1966–75 BMC ADO17 ("Landcrab") Morris 1800
- 1975–78 Princess 1.8
- 1971–78 Morris Marina 1.8
- 1964–67 TVR Grantura Mark III and IV
- 1964-65 Elva Courier Mark IV
- 1974–78 Leyland Sherpa van
- 1973–75 Hanomag F20, Hanomag F25, Hanomag F30, Hanomag F35
- 1973–77 Mercedes Benz L207
- 1973–78 Mercedes Benz L307
2.4 litre engines[]
There was a 2433 cc six-cylinder unit, named "Blue Streak", which was used in the Australian Austin Freeway and Wolseley 24/80.
See also[]
References[]
- Porter, Lindsay (1985). BMC and Leyland B-Series Engine Data. Osprey. ISBN 0-85045-597-9.
External links[]
Template:Leyland engine range
This page uses some content from Wikipedia. The original article was at BMC B-Series engine. The list of authors can be seen in the page history. As with Tractor & Construction Plant Wiki, the text of Wikipedia is available under the Creative Commons by Attribution License and/or GNU Free Documentation License. Please check page history for when the original article was copied to Wikia |